Utrack X32 USB Driver Problem

Home Page Forums Cymatic Audio Forum uTrack-X32 Utrack X32 USB Driver Problem

This topic contains 10 replies, has 3 voices, and was last updated by Didi Didi 1 year, 1 month ago.

Viewing 11 posts - 1 through 11 (of 11 total)
  • Author
    Posts
  • #29178
    Miralem
    Miralem
    Participant

    Hello,
    after installing the Utrack X32, the installation of the USB/ASIO Driver looks fine. I get the massage, that the driver is not signed …. blabla.
    But after the installation, i get error code (10) from windows (device manager), that the hardware cannot be started.

    Ok, i`ve installed the USB Driver on my Laptop and it works fine. But i can`t get the USB connection from my DAW PC.

    It`s an ASUS Board. I turned off the Driver certificates in Windows. I`ve also deinstalled the Behringer x32 USB driver …
    I tried some other USB Porst, but it looks like a windows problem.

    As usual on my DAWs, i switched of a lot of Windows services, that i dont need for propper work with windows.
    Maybe there is one service that windows need for the Utrack?
    The Behringer original USB was working well …

    Any idea?

    #29187
    Miralem
    Miralem
    Participant

    No idea?

    #29188
    Laszlo .
    Laszlo
    Keymaster

    Hi,

    Sorry for the delayed response.

    What is your OS version?
    First please remove the currently installed driver (if already installed)
    On windows 7 (64 bit) systems you need to have a Windows6.1-KB3035131-x64 hotfix installed (this update must be installed first), then reboot the computer and install the Windows6.1-KB3033929-x64.
    Reboot the pc again.
    Start the driver installer and make sure there’s no USB drive connected to your uTrack-X32. When you see that popup message connect your uTrack-X32 to the computer. The installation should succeed.

    #29189
    Miralem
    Miralem
    Participant

    Hello,
    yes its Windows 7-64.
    I`ve downloaded the hotfixes and will try later. I hope this will fix my problems.

    I was also waiting a long time for such device!!!!! very great!!!!!

    #29190
    Miralem
    Miralem
    Participant

    Ahhh, i forgot my second question.
    I`ve tried to give the Utrack an IP Adress (switched of the DHCP) but it doesnt work.

    My DAW PC is not in the same Network IP Range as my Router (Internet). But the Router is the DHCP for all Internet connections.
    So I`m not able to manage the Utrack with my DAW, as the Utrack gets the IP Range from the Router.

    #29191
    Laszlo .
    Laszlo
    Keymaster

    Hi,

    Once you disable the DHCP you need to type the IP address manually then reboot the device to apply the new parameters. Does it revert back to DHCP after rebooting the device?

    #29192
    Miralem
    Miralem
    Participant

    Yes, it reverts back to DHCP.

    #29193
    Laszlo .
    Laszlo
    Keymaster

    Whops,

    Yes you are right the DHCP/Static settings not enabled on uTrack-X32 only on uTrack24.
    We need to correct this with firmware update, please stay tuned

    #29194
    Miralem
    Miralem
    Participant

    OK, the driver works now. Muchas gracias.
    Very nice support!!! 😉

    Ok, i will wait for the update.

    #29475
    Didi
    Didi
    Participant

    Do you have any information about the release date of this firmware update?

    #33963
    Didi
    Didi
    Participant

    No new information after 5 months about this firmware update which fixes this issue?

Viewing 11 posts - 1 through 11 (of 11 total)

You must be logged in to reply to this topic.